Fuse Box / Consumer Unit Replacement Tottenham

Yes, on socket-outlet final circuits rated ≤32A — BS 7671:2018+A2:2022 §421.1.7 enforced from September 2022. For a Tottenham HMO around West Green Road or near Bruce Castle, that's AFDD-RCBOs on every sockets ring, kitchen sockets, utility sockets, and any communal-area sockets. Lighting and shower circuits stay on standard RCBO. Where Tottenham's high-density HMO conversions have shared neutrals between let areas, we re-segregate before adding AFDDs. EIC pack formatted for Haringey Council's HMO licensing scheme.

Yes — Haringey Council's HMO licensing team accepts BS 7671-certified fuse box upgrades when the pack includes the EIC, schedule of test results, and an in-date EICR. Tottenham sits inside Haringey's additional licensing scheme covering N15 and N17; the certificate pack is identical to the Wood Green format and submitted via the same portal. We issue all three as a single PDF. If you're applying for a new licence at the same time, the upgrade is sequenced to land EIC and EICR inside the application window.

Depends on the HMO type. Single-household shared houses get one consumer unit. Tottenham has a particularly high density of converted-flat HMOs — Victorian and Edwardian terraces along Bruce Grove Road and around West Green Road split into 3-5 let units. These need a separate consumer unit per let unit on a properly segregated supply. We check the existing supply arrangement at the cutout — many 1990s-era N17 conversions were done with shared neutrals and partial segregation that needs UK Power Networks involvement to fix properly.

Both protect against electric shock and electrical fire. The difference is granularity.

• RCD consumer unit (typically dual-RCD): Two big trip switches, each protecting a group of circuits. If one circuit faults, the whole RCD group trips — you lose the kitchen, lights, and sockets together.
• RCBO consumer unit (one RCBO per circuit): Each circuit has its own combined trip switch. If the kitchen socket faults, only that circuit goes off — the rest stay live.

Why we recommend RCBO for most Tottenham installs:

• Faster fault diagnosis — you know immediately which circuit is faulty
• Less disruption — one bad iron doesn't kill the whole upstairs lighting
• Better with modern electronics — RCBOs are more sensitive and reliable

When dual-RCD is fine: small flats with simple circuit layouts, properties on a tight budget, short-term landlord-let where cost beats convenience.

Cost difference: typically £150 between dual-RCD (£800) and full RCBO (£950). For most homeowners we recommend the RCBO upgrade — it pays for itself the first time a fault localises rather than killing half the house.

This is the most common scare we see in Tottenham — the fear-driven upsell to landlords.

Honest answer: plastic fuse boxes fitted before 1 January 2016 are still legal and don't automatically fail an EICR. They were the standard at the time of fitting. They become a problem only when:

• The plastic enclosure shows signs of overheating or burn marks (genuine C2)
• The board has no RCD protection on socket circuits (the fail reason isn't the plastic — it's the missing RCDs)
• The original installation was non-compliant when fitted

Since 1 January 2016, all new consumer units in domestic properties must be made of non-combustible material (typically metal). This is a forward-looking requirement — your existing plastic fuseboard doesn't get retrofitted just because the rules changed for new installs.

What you should worry about: not the colour of the box. Worry about RCD coverage, the age of the wiring, whether the existing fuse box has been properly maintained, and whether your EICR has C1/C2 codes against the consumer unit specifically. If an electrician quotes you for "a metal consumer unit because plastic fails EICR" without that nuance — get a second opinion.

Code-driven. C1 (danger present) is remediated before re-energising — same-day on install. C2 (potentially dangerous) is folded into the upgrade scope; EICR re-test issued the same day. C3 (improvement recommended) doesn't block Haringey licensing alone. Tottenham flow: EICR fail → upgrade booked within 7 days → EIC + re-test EICR on install day → Haringey portal resubmission. Inside 14 days is normal for Haringey's processing window — sometimes faster on emergency applications when a council inspection is already scheduled.

Almost always yes. The new consumer unit is the brain; your existing circuits are the nervous system. We connect to your existing circuit cables — they don't get rewired.

What we test before we commit:

• Insulation resistance on every circuit (must be at or above 1MΩ; healthy 1990s+ installs typically read above 200MΩ)
• Earth continuity — needed for RCD/RCBO to work safely
• Loop impedance — the circuit's ability to clear a fault

If a circuit fails any of these tests, we tell you before we commit. Options:

• Single circuit fix (£100-£300) — repair the fault and continue
• Targeted partial rewire of just that circuit (£300-£600)
• Hold the upgrade and discuss whether a partial or full rewire is now better value

Common Tottenham scenarios where wiring fails: 1950s-60s rubber-insulated cable in upstairs lighting circuits (Tottenham High Road and Tottenham High Road period properties), borrowed neutrals from DIY work, undersized cables on extension circuits.

We never "just power it back up" with a circuit that failed testing — that's how fires start. Honest tradeoffs only.

Honest answer: the £800 is fixed for the standard scope. Any extras are quoted upfront, never sprung on you mid-install.

What's covered in £800 (no surprise add-ons):

• The new consumer unit / fuse board (quality metal, 6-10 ways)
• RCD protection on socket and lighting circuits
• Re-terminating every existing circuit, properly labelled
• Full insulation, earth, and RCD testing on every circuit
• The Electrical Installation Certificate (EIC)
• Plaster patching with bonding plaster around the install

What CAN add to the price (we tell you before we start, with a fixed quote):

• Circuits failing insulation testing — we'll show you the readings, and you decide: targeted repair (£100-£300 per circuit) or hold the upgrade for a partial rewire conversation
• Incoming supply needs upgrading — rare; happens when adding heavy load like an EV charger or heat pump. We tell you upfront if your supply is borderline
• You opt for the premium tier — £950 (RCBO every circuit + surge protection) or £1,200+ (larger split-load board)

What we never do: discover a "problem" mid-install and charge you for it without your sign-off first. If we find something during testing, work pauses until you've decided. No scope creep.

Tottenham HMO supplies are mostly TN-C-S across N15 and N17 — older terrace stock around Bruce Castle and the West Green Road end still occasionally TT with degraded rods. Main bonding to gas and water entry required on both. Supplementary bonding in shower rooms unless every metallic service bonds back to the main earthing terminal and the room is on a 30 mA RCD. Per-flat gas/water entries bonded per-unit. Earth electrode resistance tested and recorded on the EIC; new TT rod fitted where the existing reads over 200Ω.

Single-CU Tottenham HMOs: one 2-3 hour mid-morning isolation window — every let unit off during that window. Multi-CU HMOs (one per converted flat, common in N17): sequenced swap one flat at a time so only one let unit is offline at any moment. Tenants notified 7 days ahead. Power back same evening on all routes. Temporary kitchen-ring supply available for the lunchtime window so tenants can use the kettle and microwave.

Yes — and we set up Tottenham consumer units for it as standard. What we include:

• Spare 32A way on the fuseboard, labelled and ready for a 7kW or 22kW EV charger install
• Adequate supply headroom — we check your incoming supply and tell you upfront if a heat pump or EV charger needs a supply upgrade (often the headroom is fine, but worth confirming)
• SPD (surge protection) on the premium tier (£950) — protects every modern electronic in the house from voltage spikes
• Smart-home-ready circuits — neutrals to switch positions if you specify (most period houses don't have these, blocking smart switch installs later)

What gets retrofitted later costs more. Adding an EV charger circuit to an existing fuse box: £400-£600 extra labour because we need to chase walls, lift floor coverings, and isolate the supply again. Specifying it during the consumer unit upgrade: marginal cost only.

Tell us at the survey stage what you might add in the next 5 years — EV, heat pump, hot tub, garden room, second EV charger, home office. We size the board around your plans, not just your current circuits.

Almost never. Unlike a rewire, a consumer unit replacement is contained to the meter cupboard — usually under the stairs, in a hallway recess, or in a kitchen cupboard. The work stays in that one spot.

What we do during the install:

• Disconnect existing circuits at the old fuse box, label every cable
• Remove the old fuseboard from its mounting point
• Mount the new consumer unit in the same position (same screw holes where possible)
• Re-terminate every circuit into the new board
• Test, certify, and label every circuit on the new unit's chart

What we don't do:

• Chase walls
• Lift floorboards (unless an existing cable is too short to reach the new connection point — rare)
• Disturb skirting, sockets, or switches anywhere else in the house
• Affect any decoration outside the meter cupboard

The only plaster work: if the new board is a different physical size than the old one, we may need to patch a small area of bonding plaster around the mounting position. That's included; finishing coats and any decoration are a decorator's job.

Tottenham properties with the original fuse box in a tight under-stairs space sometimes need a little extra work to fit a wider modern board — we'll show you the position before we start so you can decide whether to keep it where it is or relocate.