Lighting · heating · Home Assistant · automation
Keep the switches you already know while adding app, voice and automation control. In many Edmonton homes, suitable Shelly, Sonoff or Aqara products can be installed without new cable runs or a full rewire, and selected WiFi or Matter-over-WiFi devices need no separate hub. We check the wiring, load, network and chosen ecosystem around long terraces & divided layouts and semis with garage workspaces before confirming the right option.
The home before the technology
NICEIC-Registered Electrician D609991. Wiring, connected loads, heating interfaces and network requirements are checked before equipment is selected. Applicable electrical work is inspected, tested and certified.
The questions customers ask first
Worried about losing familiar controls, replacing everything, unreliable apps or damage to finished rooms? Here is what we check before recommending any smart-home equipment.
Manual control remains part of the design wherever the selected equipment and existing wiring support it. We check how each light, heating zone or connected device is operated now, then demonstrate both normal manual use and the smart controls at handover.
Often, no. Suitable Shelly, Sonoff or Aqara relays can retain an existing wall switch, and selected no-neutral products can avoid new cable runs or a full rewire. We check the wiring, available space, connected load and switching arrangement before identifying what genuinely needs to change.
It depends on the exact products. Local switches and controls can continue without the internet where the design supports that, while remote access, cloud automations or voice control may pause. We explain those dependencies before installation so the fallback is understood.
We inspect the wiring and likely equipment positions before agreeing the work. Existing switch positions and accessible routes are used where practical, and any deeper box, new cable route or visible alteration is discussed first. Working areas are protected and applicable electrical alterations are tested.
Start with the moment that should feel easier
The right design starts with a household need, then checks the wiring, heating, network and ecosystem needed to support it.
Swipe through the real situations
We inspect the existing switch arrangement and choose a compatible control method only after confirming how familiar manual use will remain.
The heat source, existing programmer, valves and occupied rooms are checked before compatible thermostats or room controls are proposed.
Supported products can be coordinated through Home Assistant or another suitable platform, with exact integrations checked before they enter the scope.
Every sensor is tied to a clear household outcome, with timing, override and failure behaviour agreed rather than left as a novelty.
Power, data, controls and future provision can be coordinated while access is available, avoiding unnecessary alteration after decoration.
Rooms, scenes, users, accounts and fallback controls are tested and explained so the finished system is not dependent on one person remembering how it works.
Useful control, room by room
Lighting, heating, sensors, selected appliances and scenes can work together—but only where each addition has a clear purpose and verified compatibility.
Swipe through the smart-home options
Control suitable lights from the wall, app or voice assistant; create useful evening, away or bedtime scenes; and retain a clear manual route wherever the selected equipment supports it.
Nest, Hive, Tado, Drayton Wiser and Honeywell evohome can be considered after the boiler, hot-water controls, programmer, valves and required zones are checked.
Suitable smart plugs, relays and energy-monitoring devices can add schedules, remote control or usage information without pretending every appliance should be automated.
Aqara and other compatible sensors can support lighting, alerts, comfort and safety routines when the trigger, delay and manual override are defined first.
Supported motors, lighting controls and sensors can be coordinated around access, weather exposure, safe electrical provision and the way the space is actually used.
Apple HomeKit, Alexa, Google Home, SmartThings and Home Assistant can provide different control routes, subject to the exact model, bridge, firmware and feature required.
Real installation detail
Completed dashboards, controls, sensors and labelled equipment from the Rudi Electrics portfolio. Each photograph shows a different part of a real smart-home installation.
Real reviews from homeowners across Edmonton. Live Google reviews below — for all 388+ reviews across Google, Checkatrade and MyBuilder, see our testimonials page →
The product follows the requirement
We are brand-agnostic. The recommendation follows the existing wiring, ecosystem, exact feature required and the fallback the household expects.
Swipe through brands and standards
Relays, dimmers, energy monitoring and selected no-neutral options can work behind familiar controls or in a suitable enclosure. Exact wiring and offline behaviour are verified by model.
Switches, hubs, presence, motion, door, temperature and blind products can suit Apple-focused or multi-platform homes when the required hub and feature support are confirmed.
WiFi, Matter and Zigbee options cover relays, wall panels, plugs and sensors. Existing eWeLink or Home Assistant setups can be incorporated where the exact device is supported.
Connected lighting can create useful scenes indoors and outside. Bridge, local-control, wall-control and ecosystem requirements are agreed for the chosen products.
Thermostats, receivers and room controls are chosen from the real heating system and desired zoning, not from a brand name alone.
These technologies affect hubs, border routers, range and local operation. We check the exact product architecture so the network and control plan are honest.
Home Assistant, configured by Rudi
Home Assistant can bring supported lighting, heating, sensors and security into one clear dashboard. We configure it around the equipment you already own and compatible Shelly, Sonoff, Aqara, Philips Hue or Govee devices installed in Edmonton.
From everyday need to confident handover
The timescale is confirmed after the scope, existing systems and access have been checked. The same team then follows the agreed plan through installation, configuration and handover.
Swipe through the installation process
We identify the daily frustrations, the controls people already understand and the small number of outcomes that would genuinely improve the home.
Switch wiring, back-box space, lighting loads, heating interfaces, WiFi coverage and practical equipment positions are checked before products are selected.
The proposal names the products, rooms, controls, integrations, visible alterations, dependencies and price so the finished behaviour is clear.
Electrical and low-voltage work follows the agreed positions and routes, with work areas protected and applicable electrical alterations completed safely.
Devices, hubs, apps and supported integrations are organised around the household, then useful scenes and routines are configured rather than left unfinished.
Manual and smart operation, outage behaviour, account ownership and maintenance access are demonstrated, with applicable electrical certification supplied.
This reflects a real-world smart-home situation we come across frequently in Edmonton: the useful answer starts with existing wiring, equipment and household habits, not a pre-selected product bundle.
We identify the daily routines, frustrations and controls that already work well.
Wiring, loads, heating interfaces, network coverage and exact product compatibility are checked.
The simplest suitable controls, integrations and automations are installed and configured.
Manual use, app control, accounts and outage behaviour are tested and explained.
What the customer is really buyingA home that feels easier to use, while the technology stays quietly in the background.
Comfort should feel natural, not complicated
Keep the switches you already know while adding app, voice and automation control. In many Edmonton homes, suitable Shelly, Sonoff or Aqara products can be installed without new cable runs or a full rewire, and selected WiFi or Matter-over-WiFi devices need no separate hub. We check the wiring, load, network and chosen ecosystem around long terraces & divided layouts and semis with garage workspaces before confirming the right option.
Long Terraces & Divided Layouts and semis with garage workspaces create different wiring, network and control decisions in Edmonton. The survey follows the actual property rather than assuming one smart-home bundle will suit both.
For Long Terraces & Divided Layouts, the survey records switch wiring, load type and the manual control that must remain available. The control method is then chosen from the verified wiring and the ecosystem the customer wants to use. That keeps the visible controls familiar while the automation behind them remains deliberate and maintainable.
Keep ordinary controls obvious, make automations genuinely useful and explain every dependency before handover.
The area is not one property type
Existing wiring, heating controls, ownership, finishes and network coverage all affect which controls and integrations make sense. These four local contexts explain what we look for at survey.
Swipe through the property contexts
Edmonton N9 and N18 · Long Terraces & Divided Layouts
How should lighting controls be planned for Long Terraces & Divided Layouts in Edmonton? For Long Terraces & Divided Layouts, the existing switch wiring, connected load and desired manual operation are checked before the lighting-control method is selected.
For Long Terraces & Divided Layouts, the survey records switch wiring, load type and the manual control that must remain available. The control method is then chosen from the verified wiring and the ecosystem the customer wants to use. The plan also accounts for coverage past solid walls in Edmonton.
Edmonton N9 and N18 · Semis With Garage Workspaces
What should be checked before adding heating and room controls to Semis With Garage Workspaces? For Semis With Garage Workspaces, heating zones and temperature sensing are planned with the new room use and the existing heating system rather than added as isolated app controls.
Heating control for Semis With Garage Workspaces starts with the boiler or heat source, existing programmer, valves and desired zones. That prevents a product being specified before the system interface is known. The plan also accounts for wired work connections in Edmonton.
Edmonton N9 and N18 · Flats With One Telecoms Point
How should network coverage and hub positions be planned for Flats With One Telecoms Point? For Flats With One Telecoms Point, the network and hub stay within the private installation where possible, and any shared-area route is identified before the quotation.
For Flats With One Telecoms Point, the survey checks WiFi coverage, Ethernet options and practical hub or bridge positions. The equipment plan follows those findings and the devices being connected. The plan also accounts for useful socket positions in Edmonton.
Edmonton N9 and N18 · Rear Extensions & Garden Offices
How can CCTV, doorbell or later automation be allowed for in Rear Extensions & Garden Offices? For Rear Extensions & Garden Offices, routes for CCTV, doorbells, blinds or later controls are identified while access is available, with only the agreed equipment included in the quotation.
Future provision for Rear Extensions & Garden Offices is limited to identified power, data and containment routes. CCTV, doorbell and automation compatibility remain explicit parts of the written scope. The plan also accounts for permanent remote links in Edmonton.
Connected local smart-home guidance
Smart-home installation in four nearby parts of our wider Enfield service area. Select a linked location for more local guidance, or ask us about another nearby address.
Straight answers before installation
Property-specific answers for Edmonton, followed by practical guidance on the brands, controls, protocols and integrations we install.
The £250 starting price covers a basic smart home setup — typically:
Everything else is quoted after a free site survey. Typical project ranges:
What changes the quote: number of switches, neutral-wire availability, ceiling rose access for relays, hub or local-server requirements, ecosystem (Alexa / Google / HomeKit / Home Assistant), and integration complexity.
Why hire a qualified electrician vs. an Instagram ‘smart home installer’: we’re NICEIC-registered electricians first, smart-home specialists second. We don’t just configure your app — we make sure the lighting circuits are safe, back boxes are deep enough for relays, heating controls are wired to current regulations, and relay terminations are rated for the load. The smart bit is the easy bit; the wiring is what makes the install safe and lasting.
One trip, fixed quote, no daily-rate creep.
Four paths, each with trade-offs:
Smart bulbs (Hue, Govee, LIFX, Wiz) — easiest, cheapest entry point. Replace your existing bulbs with WiFi/Zigbee bulbs, control via app or voice. Limitation: if you turn off the wall switch, the bulb has no power and goes dumb (see Q8 for fix).
Smart switches (replace the wall switch entirely) — proper smart control, works whether someone touches the switch or not. Limitation: UK houses often don’t have a neutral wire at the switch, which most smart switches need (see Q3).
Smart plugs (smart sockets / WiFi plugs) — for table lamps, kettles, fans, anything plugged in. Easy, no wiring needed.
Smart relays — Shelly + Aqara — our most-recommended retrofit. Tiny relays installed in the back box behind your existing switch. Your original switch still works AND the light becomes smart-controllable. Preserves period-property fittings, designer switch plates, expensive existing lights. Aqara has no-neutral options too.
Our default for whole-house: Shelly or Aqara relays for switches you want to keep + Hue or Govee bulbs where you want colour or effects.
Common UK old-house problem. British lighting circuits typically wire the switch with a permanent live + switched live only — the neutral lives at the ceiling rose, not the switch. Most smart switches need neutral to power their electronics.
Three solutions we use:
Best path for most older Edmonton homes: option 1 — relay at the ceiling rose. This approach can retain the switch plates and avoid wider decoration where the ceiling rose, enclosure and wiring provide suitable access.
Honest version: cross-platform support varies by device, Matter support and integration, so we confirm the products you want to combine before choosing the main control platform.
Amazon Alexa (Echo) — most third-party device support, casual-friendly, cheap. Best for ‘I want to plug things in and forget’.
Google Home (Nest) — better voice recognition, smart phone tie-in. Good for Android households.
Apple HomeKit — best privacy and security, premium build quality. Limited device range, more expensive. Best for Apple-heavy households.
Home Assistant (HA) — what we install for serious smart-home customers. Open-source platform whose core runs locally on your network and supports a wide range of confirmed integrations: Hue, Govee, Shelly, Aqara, Nest, Hive, Tado, Sonos, your CCTV, your thermostats — available through one dashboard where the confirmed integrations support the required functions. Privacy-respecting. We’re Home Assistant experts — see Q11.
Default recommendation: Alexa or Google for casual users, Home Assistant for anyone who wants real control, privacy, or to mix multiple brands.
Smart heating can reduce unnecessary heating where schedules, zoning or occupancy control improve on the previous setup, but the result varies with the property, system, settings and earlier usage. Published manufacturer and study figures provide context rather than a guaranteed saving for an individual home.
Where smart heating actually pays off:
Brand picker: Nest for combi-boiler households, Hive or Tado for hot-water + heating control, Drayton Wiser for budget zone control, Honeywell evohome for premium full-zone setup. We install all of them and integrate them into Home Assistant if you want unified dashboards.
For most homeowners, no — modern brands handle this for you. Quick rundown anyway:
What this means for you: if you’re starting fresh, consider Matter-compatible products where their exact features and ecosystem support meet the brief. We default-install Zigbee for Hue + Aqara, WiFi for Shelly + Govee, all unified through Home Assistant if you go that route.
A hub is a small box that talks to your smart devices and your WiFi/voice assistant. Whether you need one depends on the protocol your devices use:
The main hubs:
Our default: if you’ve got 1–2 brands, brand hub. If you’ve got 3+ brands or want privacy, Home Assistant.
Universal smart-bulb pain. When the switch is off, the bulb has no power, so the app or voice can’t reach it. Three fixes, in order of how we install them:
For Edmonton customers with existing Hue or Govee bulbs, Shelly relay retrofit is the cleanest fix — final price quoted after we see the back box depth and neutral availability.
Local behaviour during an internet outage depends on the selected devices and integrations. We plan essential manual control and explain which automations, apps or remote features rely on the router, internet or a manufacturer cloud service.
How we ensure local-only operation:
What stops working without internet: voice control where the configured assistant depends on its cloud service, remote access from outside the house, and pure cloud-only brands (Govee WiFi-only app control). Suitable physical controls are retained and tested where the selected device and wiring arrangement support them.
Our default install — Hue Bridge + Shelly/Aqara relays + Home Assistant — is designed so the agreed local controls do not depend solely on an internet connection. We test and explain how the wall switches operate, including what happens if the hub or internet connection is unavailable.
Yes — most things you can think of. What we install:
For full integration: Home Assistant can bring supported devices into one dashboard and coordinated automations — ‘when last person leaves home, lock door, arm cameras, turn off all lights, set heating to away’.
Yes — we’re Home Assistant experts and HA is what we recommend for serious smart-home customers. What you get:
What we install:
Not for everyone — HA needs you to be comfortable tinkering. For ‘set and forget’, stick with Alexa or Google.
Depends on scope:
During the install:
Hand-over:
12-month install warranty: if anything we installed stops working within the first year, ring us and we’ll come back at no extra charge. After 12 months, our standard £100 callout applies. Most issues troubleshoot remotely first.
We install and configure Philips Hue, Govee, Shelly, Sonoff and Aqara products, including suitable bulbs, switches, relays and sensors. The right approach depends on the existing switch wiring, neutral availability, back-box depth, connected load and whether familiar manual control must remain. We check those details before recommending equipment rather than forcing every home into one brand.
Often, yes. Suitable Shelly, Sonoff or Aqara relays can be fitted behind an existing switch or at the light fitting, allowing the familiar wall control to remain. Selected no-neutral products also avoid running a new neutral to the switch. This can mean no replacement switch, no new cable runs and no full rewire, but we first check the available space, switching arrangement, lamp or load compatibility and circuit condition. Any bypass, deeper box or wiring alteration that is genuinely needed is agreed before work starts.
We install Nest, Hive, Tado, Drayton Wiser and Honeywell evohome. Before specifying a thermostat, receiver or smart radiator valve, we check the boiler or heat source, hot-water controls, existing programmer, valves and the rooms you want to control. Published figures give useful context: Google reports average Nest Learning Thermostat heating savings of 10–12%, while tado cites average heating-energy savings of 22% and up to 28% in studied conditions. These are manufacturer and study figures, not a guaranteed saving for every home; the result depends on the property, heating system, settings and previous usage.
Surveyed, installed and explained by one team
Arrange a free consultation to decide what should stay familiar, what should become connected and how the finished system should behave every day.
NICEIC registration D609991 (verify) · 15+ years’ experience working across North London. Applicable electrical work is inspected, tested and certified, with Part P notification where required, and our workmanship is guaranteed for 12 months.
Tell us about your home and what you'd like to control — we'll get back to you After survey with a free quote.
We install and configure Shelly devices professionally — no hub required, works with Alexa, Google Home & HomeKit.
All smart home wiring is carried out safely by a qualified electrician. You receive full certification on completion.
We configure every device, set up your automations, and walk you through how it all works before we leave.
From £250 per smart switch. No surprises — we agree the price before any work begins.
